Analytics

With your agreement, we use Google Analytics to count visits and improve this site. No advertising. Without your agreement, nothing is loaded. Learn more

Skip to content
TOPRANK Europe
All articles

Workshop · Workshops and builds

Harry's R33 GT-R: a customer build at TOPRANK, step by step

A Skyline GT-R R33 V-Spec, an engine rebuilt by the group's workshop near Fuji, then a new front end fitted and painted at Toprank Classic Specialities. The story of one customer car, as TOPRANK documented it.

Published on · 6 min read · TOPRANK Europe

White Skyline GT-R R33 with a black bonnet and a new front bumper, finished, in the TOPRANK Classic Specialities building

Between July 2025 and September 2026, the TOPRANK group published four articles and one video about the same car: the Skyline GT-R R33 of a customer the group calls Harry. Together they show what a project in the group's workshops looks like, from the engine to the paint.

Everything below comes from these pages. The figures are TOPRANK's.

The car

The base is a Nissan Skyline GT-R R33 V-Spec, in white. TOPRANK describes the project not as a restoration but as a car reimagined from the ground up, around what the owner wanted.

Two of the group's workshops took part. Shizuoka Technical Factory (STF), TOPRANK's workshop near Fuji Speedway, handled the mechanical side. Toprank Classic Specialities (TCS) handled the body.

Step 1: the engine, at STF

In July 2025, TOPRANK presented the mechanical build. According to the group, the work was led by its master mechanic, Sato-san. The main points:

  • The engine: a fully rebuilt RB26DETT, the original GT-R straight six.
  • The turbo: a Garrett single turbo replaces the two original turbos.
  • The gearbox: a modern sequential transmission.
  • The rest: TOPRANK mentions the engine build, the transmission set-up and chassis reinforcement.

In November 2025, TOPRANK put the result at about 700 horsepower. The group describes a road car, built for spirited driving on the open road and in the mountains.

What the owner wanted

The group filmed an interview with Harry, published on its YouTube channel under the title “Toprank Classic Specialities × STF: R33 GT-R Tuning Project | Customer Interview”. In it he explains why he chose the R33 and how the build went.

TOPRANK sums up his main point as balance: a car that is not tiring to drive every day, but gives its power the moment it is needed. The group adds that Harry and the STF team see the car as a long-term companion. It was developed with maintenance and long life in mind, not as a one-off tuning job.

Step 2: the body, at TCS

In August 2026, the car went to TCS for a major change of its exterior: a TOP SECRET front bumper and a selected combination of aftermarket aero parts.

White Skyline GT-R R33 on stands in the TCS workshop, bonnet open, new front bumper and wings in primer with masking tape
August 2026: the new front parts are fitted and adjusted before paint.

These parts are made of FRP, fibre-reinforced plastic. TOPRANK explains why that takes time. Unlike factory panels, aftermarket FRP parts rarely fit straight out of the box. The gaps, the alignment, the mounting points and the way each part flows into the next all need adjusting. In the group's words, bolting the parts on is easy; making them look as if they belong to the car is the hard part.

The TCS body specialists list what they work on:

  • precise fitting and adjustment of the FRP parts;
  • even panel gaps;
  • correct alignment between the bumper, the wings and the panels around them;
  • careful preparation before paint;
  • a finish that respects the original lines of the R33 GT-R.
Front wing of the white R33 GT-R being test-fitted, with the wheel removed and a large blue brake caliper visible
Test fitting of a front wing at TCS.

Step 3: the result

In September 2026, TOPRANK announced that the work was finished. After many hours of fitting, adjustment, preparation and paint, the new parts were painted to match the rest of the car. The stated aim: nothing should look out of place.

The group calls the car “the White Devil”. It writes that the R33 has an entirely new presence, while keeping its unmistakable R33 character.

Close-up of the finished front: white bumper with air intakes, GT-R badge, black carbon bonnet and a TOPRANK Classic Specialities plate
September 2026: the finished front end.

What this project shows

Harry's car shows how the group splits the work: the mechanical side at STF, the body at TCS, each with its own specialists. It also shows the time involved: for the bodywork alone, TOPRANK speaks of countless hours of fitting, adjustment, preparation and paint.

The same workshops can work on your car in Japan, during storage or before it ships to Europe. Each project gets its own written quote.

Questions and answers

Can I have the same build done on my car?

Each project is different and starts with a discussion and a written quote. The Tuning Program page explains how a project goes.

Does my car need to be in Japan?

The work is done in Japan. A car bought there, or stored there by TOPRANK, can be prepared before it is shipped.

Can a car modified like this be registered in Europe?

A modified car does not take the same route as a car in original condition. We tell you which route applies before the work starts.

See the Tuning Program

Store your car in Japan

Sources

The facts in this article come from the sources below.

Your plans

A question about your car?

Tell us what you are looking for. We answer in French, English or German.